產(chǎn)品名稱：RatCytokineArrayQ67

• Running an array is like running dozens of ELISAs simultaneously.
• Quantibody arrays are stunningly simple to use, read, and analyze.
• Each panel can quantify up to 40 different biomarkers simultaneously, and individual panels can be multiplexed to quantify as many as 660 different biomarkers at one time.
• The entire process can be completed in just 4-6 hours.
• More cost-effective than traditional ELISA
• High specificity and system reproducibility
• Suitable for diverse sample types
• Low sample volume requirement: 50 μL or less
• Well-suited for high throughput assays

• More cost-effective than traditional ELISA
• High specificity and system reproducibility
• Suitable for diverse sample types
• Low sample volume requirement: 50 μL or less
• Get results same day (6-hour processing time)
• Well-suited for high throughput assays
• Q Analyzer software provides one-step computation

The Quantibody arrays are quantitative multiplex ELISA arrays featuring fluorescent detection. The antibodies are spotted on glass slide solid supports and require a laser scanner for data collection. Cytokine standards are provided with the array for calculation of target protein concentrations. All Quantibody arrays feature the sandwich immunoassay principle, utilizing an immobilized capture antibody along with a corresponding biotinylated detection antibody.

1. Each Quantibody array starts with a single glass microscope slide, which acts as a support for the array. Slides are segmented using a rubber gasket. Up to 8 samples may assayed using a single slide.
2. Antibodies against a variety of different antigens (up to 40 biomarkers per slide) are printed onto the glass slide. Replicates are included, saving you both time and precious sample volume.
3. The end-user adds either known concentration standards (included) or aqueous sample to each well on the slide. Antibodies on the slide capture antigen off from the sample or standard.
4. The end-user adds a detection mix containing paired antibodies (compatible with the primaries pre-coated on the slide) conjugated to a fluorescent dye for detection.
5. Fluorescent signal from each spot is read using a laser slide scanner. The intensity from each spot is compared to the standard curve, and a quantitative expression profile for relevant biomarkers is established.

1. Take out the glass slide from the box, and let it equilibrate to room temperature inside the sealed plastic bag for 20-30 minutes. Remove slide from the plastic bag, peel off the cover film, and let it air dry for another 1-2 hours.
   2. Reconstitute the Cytokine Standard Mix (lyophilized) by adding 500 μl Sample Diluent to the tube. For best recovery, always quick-spin vial prior to opening. Dissolve the powder thoroughly by a gentle mix. Labeled the tube as Std1.
   3. Label 6 clean microcentrifuge tubes as Std2 to Std7. Add 200 μl Sample Diluent to each of the tubes.
   4. Pipette 100 μl Std1 into tube Std2 and mix gently. Perform 5 more serial dilutions by adding 100 μl Std2 to tube Std3 and so on.
   5. Add 100 μl Sample Diluent to another tube labeled as CNTRL. Do not add standard cytokines or samples to the CNTRL tube, which will be used as negative control. For best results, include a set of standards in each slide.
   6. Add 100 μl Sample Diluent into each well and incubate at room temperature for 30 minutes to block slides.
   7. Decant buffer from each well. Add 100 μl standard cytokines or samples to each well. Incubate arrays at room temperature for 1-2 hour.
   8. Wash:
   - Decant the samples from each well, and wash 5 times (5 min each) with 150 μl of 1X Wash Buffer I at room temperature with gentle rocking. Completely remove wash buffer in each wash step. Dilute 20x Wash Buffer I with H2O.
   - Decant the 1x Wash Buffer I from each well, wash 2 times (5 min each) with 150 μl of 1X Wash Buffer II at room temperature with gentle rocking. Completely remove wash buffer in each wash step. Dilute 20X Wash Buffer II with H2O.
   9. Reconstitute the detection antibody by adding 1.4 ml of Sample Diluent to the tube. Spin briefly.
   10. Add 80 μl of the detection antibody cocktail to each well. Incubate at room temperature for 1-2 hour.
   11. Decant the samples from each well, and wash 5 times (5 mins each) with 150 μl of 1X Wash Buffer I and then 2 times with 150 μl of 1x Wash Buffer II at room temperature with gentle rocking. Completely remove wash buffer in each wash step.
   12. After briefly spinning down, add 1.4 ml of Sample Diluent to Cy3 equivalent dye-conjugated streptavidin tube. Mix gently.
   13. Add 80 μl of Cy3 equivalent dye-conjugated streptavidin to each well. Cover the device with aluminum foil to avoid exposure to light or incubate in dark room. Incubate at room temperature for 1 hour.
   14. Decant the samples from each well, and wash 5 times (5 mins each) with 150 μl of 1X Wash Buffer I at room temperature with gentle rocking. Completely remove wash buffer in each wash step.
   15. Disassemble the device by pushing clips outward from the slide side. Carefully remove the slide from the gasket.
   16. Place the slide in the Slide Washer/Dryer (a 4-slide holder/centrifuge tube), add enough 1x Wash Buffer I (about 30 ml) to cover the whole slide, and then gently shake at room temperature for 15 minutes. Decant Wash Buffer I. Wash with 1x Wash Buffer II (about 30 ml) and gently shake at room temperature for 5 minutes.
   17. Remove water droplets completely by gently applying suction with a pipette to remove water droplets. Do not touch the array, only the sides.
   18. Imaging: The signals can be visualized through use of a laser scanner equipped with a Cy3 wavelength (green channel) such as Axon GenePix. Make sure that the signal from the well containing the highest standard concentration (Std1) receives the highest possible reading, yet remains unsaturated.

Data extraction can be done using the GAL file that is specific for this array along with the microarray analysis software (GenePix, ScanArray Express, ArrayVision, MicroVigene, etc.).